Dewalt Laser Distance Meter DWHT77100 (0.2 to 30 m Range, Laser Class 2, Measurement Tolerance: +/- 3 mm / 10 m, Length, Areas, Volume & Pythagoras Measurements, Easy Operation)

Product Information

From the same point, aim the laser straight ahead toward the lowest point of the building or object (Figure I3). Slide the pins at the bottom of the battery door into the notches in the battery compartment (Figure E ).

Product must be currently advertised in print or electronic media (Including newspaper, catalogue, radio, television advertising or online) Point the laser at the top of the tool laser (Figure A ) toward the wall or object whose distance you need to measure.

Specification

From the same point, aim the laser straight ahead toward the center of the building or object (Figure J3). While the laser tool is in operation, be careful not to expose your eyes to the emitting laser beam (red light source). Exposure to a laser beam for an extended time period may be hazardous to your eyes. Do not look into the beam with optical aids. Press On button (Figure A ) to measure the distance from the tool to the wall or object. Refer to Setup LDM to change the reference location and / or unit of measurement.

Position the tool at one end of the target and point the laser dot across the length. (Figure H ) shows where to position the tool if you are measuring from the top of the tool.) Position the tool at one end of the target and point the laser dot across the width. (Figure G shows where to position the tool if you are measuring from the top of the tool.) Once the current measurement is taken (the device is not in Continuous Measure mode), you can change the unit of measure from decimal ft (6.21 ft) to fractional ft (6'02"9/16), fractional ft to meters (1.894 m), meters to inches (74 9/16 in), or inches to decimal ft. Total Tools reserve the right to terminate or amend the price guarantee policy at any time without notice. For Further InformationNOTE: If Second measurement is larger than first: IC 601 will be displayed for a negative number. Please switch measurement points so first measurement is larger than second. NOTE: Ensure the batteries are inserted in the correct manner, with the correct polarity. Setup (Load Batteries)

At the bottom of the display window (Figure A ), view the current measurement (Figure C ), which will keep changing as you move the tool. Total Tools reserve the right to change or withdraw free delivery at any time. Estimated Delivery Timeframes Position the tool at one end of the target and point the laser dot across the width. (Figure H ) shows where to position the tool if you are measuring from the top of the tool.) You can use the distance to two points on a tall object (Indirect Height) to determine its height (Figure I1). To change the measurement unit, hold the gear button (Figure A ) for three seconds to enter the units menu. Press the on button to confirm your reference location. Once confirmed, the current unit of measurement will be displayed, press the gear to change units and the on button to confirm.

The DWHT77100 tools emit a visible laser beam, as shown in Figure A . The laser beam emitted is Laser Class 2 per IEC 60825‑1. Should you find one day that your DeWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. DeWALT provides a facility for the collection and recycling of DeWALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

Press the gear button (Figure A ) three times to show the indirect measurement height on the display window (Figure E ). Insert two AAA batteries, making sure to position the ‑ and + ends of each battery as noted inside the battery compartment (Figure E ). To reduce the risk of injury, user must read the Product User manual, Laser Safety manual, and Battery Safety information. Switch the device on/off several times. If error still occurs, return device to Service Center or Distributor Press the gear button (Figure A ) three times to show pythagoras (Figure B ) on the display window.The following label information is placed on your laser tool to inform you of the laser class for your convenience and safety. Press and hold the gear button (Figure A ) for 3 seconds. The measurement reference location icon (Figure C ) will flash on the display window. If INFO appears on the display window with a Code number, perform the corresponding Corrective Action. Code Carefully read the Safety Instructions and Product Manual before using this product. The person responsible for the product must ensure that all users understand and adhere to these instructions.